Friday 04 2020

AD5933 - Part4 (Arduino Library Example)

AD5933 - Part4 (Arduino Library Example)

2016may04


/*
ad5933-test
Reads impedance values from the AD5933 over I2C and prints them serially.
*/
#include <Wire.h>
#include "AD5933.h"
#define START_FREQ (80000)
#define FREQ_INCR (1000)
#define NUM_INCR (40)
#define REF_RESIST (10000)
double gain[NUM_INCR+1];
int phase[NUM_INCR+1];
void setup(void)
{
// Begin I2C
Wire.begin();
// Begin serial at 9600 baud for output
Serial.begin(9600);
Serial.println("AD5933 Test Started!");
// Perform initial configuration. Fail if any one of these fail.
if (!(AD5933::reset() &&
AD5933::setInternalClock(true) &&
AD5933::setStartFrequency(START_FREQ) &&
AD5933::setIncrementFrequency(FREQ_INCR) &&
AD5933::setNumberIncrements(NUM_INCR) &&
AD5933::setPGAGain(PGA_GAIN_X1)))
{
Serial.println("FAILED in initialization!");
while (true) ;
}
// Perform calibration sweep
if (AD5933::calibrate(gain, phase, REF_RESIST, NUM_INCR+1))
Serial.println("Calibrated!");
else
Serial.println("Calibration failed...");
}
void loop(void)
{
// Easy to use method for frequency sweep
frequencySweepEasy();
// Delay
delay(5000);
// Complex but more robust method for frequency sweep
frequencySweepRaw();
// Delay
delay(5000);
}
// Easy way to do a frequency sweep. Does an entire frequency sweep at once and
// stores the data into arrays for processing afterwards. This is easy-to-use,
// but doesn't allow you to process data in real time.
void frequencySweepEasy() {
// Create arrays to hold the data
int real[NUM_INCR+1], imag[NUM_INCR+1];
// Perform the frequency sweep
if (AD5933::frequencySweep(real, imag, NUM_INCR+1)) {
// Print the frequency data
int cfreq = START_FREQ/1000;
for (int i = 0; i < NUM_INCR+1; i++, cfreq += FREQ_INCR/1000) {
// Print raw frequency data
Serial.print(cfreq);
Serial.print(": R=");
Serial.print(real[i]);
Serial.print("/I=");
Serial.print(imag[i]);
// Compute impedance
double magnitude = sqrt(pow(real[i], 2) + pow(imag[i], 2));
double impedance = 1/(magnitude*gain[i]);
Serial.print(" |Z|=");
Serial.println(impedance);
}
Serial.println("Frequency sweep complete!");
} else {
Serial.println("Frequency sweep failed...");
}
}
// Removes the frequencySweep abstraction from above. This saves memory and
// allows for data to be processed in real time. However, it's more complex.
void frequencySweepRaw() {
// Create variables to hold the impedance data and track frequency
int real, imag, i = 0, cfreq = START_FREQ/1000;
// Initialize the frequency sweep
if (!(AD5933::setPowerMode(POWER_STANDBY) && // place in standby
AD5933::setControlMode(CTRL_INIT_START_FREQ) && // init start freq
AD5933::setControlMode(CTRL_START_FREQ_SWEEP))) // begin frequency sweep
{
Serial.println("Could not initialize frequency sweep...");
}
// Perform the actual sweep
while ((AD5933::readStatusRegister() & STATUS_SWEEP_DONE) != STATUS_SWEEP_DONE) {
// Get the frequency data for this frequency point
if (!AD5933::getComplexData(&real, &imag)) {
Serial.println("Could not get raw frequency data...");
}
// Print out the frequency data
Serial.print(cfreq);
Serial.print(": R=");
Serial.print(real);
Serial.print("/I=");
Serial.print(imag);
// Compute impedance
double magnitude = sqrt(pow(real, 2) + pow(imag, 2));
double impedance = 1/(magnitude*gain[i]);
Serial.print(" |Z|=");
Serial.println(impedance);
// Increment the frequency
i++;
cfreq += FREQ_INCR/1000;
AD5933::setControlMode(CTRL_INCREMENT_FREQ);
}
Serial.println("Frequency sweep complete!");
// Set AD5933 power mode to standby when finished
if (!AD5933::setPowerMode(POWER_STANDBY))
Serial.println("Could not set to standby...");
}






Joe Biden

RCA Tunnel Diode Manual - RCA 1966

 RCA Tunnel Diode Manual - RCA 1966 https://www.yumpu.com/en/document/read/23901571/rca-tunnel-diode-manual